
What this valve is
The Kailing angle seat valve is a pneumatically actuated Y-type valve: the seat sits at roughly 45° to the flow axis, so the piston actuator and the flow path share one compact body. The stainless steel 316 body and PN16 pressure class make it a practical choice for hot water, saturated steam and mildly corrosive process media in water treatment plants and oil & gas utility systems.
Because the actuator is pneumatic rather than solenoid-operated, the valve keeps its full pressure and temperature rating without a coil winding in the media path. Control comes from an external 5/2 or 5/3 solenoid valve feeding the actuator ports — the same architecture used on packaging, sterilizing and washdown lines across Europe and North America.
Where it fits in water treatment and oil & gas
Typical duties for this Y valve include:
- Water treatment: dosing and transfer lines, filter in/outlet switching, CIP and backwash loops, demineralized and RO permeate service — duties also covered in our guide to angle seat valves for desalination plants.
- Oil & gas utilities: cooling-water and glycol circuits, steam tracing headers, washdown and drain lines, where a 316 body resists chlorides better than brass or 304.
- General process: hot water up to high temperature ranges and saturated steam, with PTFE seat sealing as the standard choice for steam duty.
The angle seat geometry gives a high flow coefficient for its port size and a short stroke, so the valve opens and closes quickly on compressed air with minimal water hammer compared with a slow-rising gate valve.
Key specifications
| Parameter | Typical configuration |
|---|---|
| Body material | Stainless steel 316 |
| Pressure class | PN16 |
| Function | 2/2-way, angle seat (Y body), pneumatically actuated |
| Ports | Threaded (G/NPT); sizes typically DN15–DN50 |
| Seat seal | PTFE for steam and hot water; options by media |
| Media | Water, hot water, saturated steam, glycol, mild chemicals |
| Media temperature | Up to approximately 180 °C with PTFE seat (confirm per size) |
| Actuator | Stainless piston actuator, single-acting (spring return) or double-acting |
| Control | External 5/2 or 5/3 solenoid valve; NAMUR or direct porting |

Selection checks before you order
- Media and temperature. Confirm the exact media (steam pressure, water temperature, chemical concentration). PTFE covers most steam and hot-water duty; other seals are available for specific media — send us the media sheet and we will confirm the seal choice.
- Pressure class and differential. PN16 covers most plant utility lines; verify the maximum differential the actuator must close against at your minimum pilot pressure.
- Flow. Angle seat valves offer a high Kv per port size; share your required flow and allowed pressure drop and we will confirm the size rather than defaulting to the line diameter.
- Actuator and control. Choose spring-return (fail-safe) or double-acting depending on your fail position requirement, and confirm the available pilot pressure for the actuator.
- Connection. Threaded G or NPT is standard for these sizes; tell us your piping standard so threads match without adapters.
FAQ
What is the difference between an angle seat valve and a solenoid valve?
A solenoid valve moves the seal with a coil directly; an angle seat valve moves it with an air-fed piston. That keeps the coil out of the hot media path, so angle seat valves handle higher media temperatures and offer a higher flow coefficient at the same port size, while a small external solenoid valve provides the electrical control.
Can this valve handle saturated steam?
Yes — with a PTFE seat seal it is designed for saturated steam and hot water duty. Confirm the steam pressure and temperature against the size-specific rating when you request a quote.
What actuation options are available?
Single-acting (spring return to closed or open) and double-acting piston actuators are available. The actuator is fed by an external 5/2 or 5/3 solenoid valve, so your PLC or control panel switches a low-power pilot valve rather than driving the process valve directly.
Request a quote
Ningbo Kailing Pneumatic manufactures angle seat valves and solenoid valves in its own factory and supports OEM marking and export documentation for US and European buyers. Send us your media, temperature, pressure, connection and quantity, and our engineers will confirm the model, seal and actuator configuration with a quotation and lead time.
Need a quotation?
Send the page link, quantity, drawings and working conditions to Kailing for review.